1203-CN1端子模块英文说明硬件设置子菜单（S5.7）提供参数
为了设置关于内部制动电阻器连接的信息,
风扇控制,键盘确认超时和键盘
检索制动器
使用此功能,您可以告诉SVX9000/SPX9000内部制动电阻是否已连接。
如果您的驱动器具有内部制动电阻,则此参数的默认值为“已连接”。但是,如果有必要增加
通过安装外部制动电阻的制动能力,或者如果内部制动电阻断开,建议更改该值
将该功能设置为“未连接”,以避免不必要的故障跳闸。
注意：制动电阻器可作为所有驱动器的选件。它可以安装在框架尺寸FR4至FR6的内部。
5.7.2
风扇控制
范围：连续,温度,初次启动和计算温度默认值：连续
风扇控制
此功能允许您控制SVX9000/SPX9000的冷却风扇。您可以将风扇设置为运行：
1台连续风机连续运行。
2基于装置温度的温度。当散热器温度达到时,风扇将自动打开
60°C。当散热器温度降至55°C时,风扇收到停止命令。风扇运行了大约一分钟
接收停止命令或接通电源,以及将值从“连续”更改为“温度”后。
3通电后首先启动风扇,直到发出运行命令,然后风扇继续运行。这主要是由
用于普通直流总线系统,以防止冷却风扇在通电时加载充电电阻器。
4冷却风扇的Calc Temp启动基于计算的IGBT温度。当IGBT温度=40°C时,风扇启动
当温度降至30°C时,风扇停止。
注意：当SVX9000/SPX9000处于运行状态时,无论该设置如何,风扇都会连续运行1203-CN1端子模块英文说明

1203-CN1端子模块英文说明The Hardware Settings submenu (S5.7) provides parameters
for setting information on Internal brake resistor connection,
Fan control, Keypad acknowledge timeout, and Keypad
retriesInternbrakeres
With this function, you tell the SVX9000/SPX9000 whether the internal brake resistor is connected or not.
If your drive has an internal brake resistor, the default value of this parameter is “Connected”. However, if it is necessary to increase
braking capacity by installing an external brake resistor, or if the internal brake resistor is disconnected, it is advisable to change the value
of this function to “Not Connected” in order to avoid unnecessary fault trips.
Note: The brake resistor is available as an option for all drives. It can be installed internally in frame sizes FR4 to FR6.
5.7.2
Fan Control
Range: Continuous, Temperature, First Start, and Calc Temp Default: Continuous
Fan Control
This function allows you to control the SVX9000/SPX9000’s cooling fan. You can set the fan to run:
1 Continuous—fan runs continuously.
2 Temperature—based on the temperature of the unit. The fan is switched on automatically when the heatsink temperature reaches
60°C. The fan receives a stop command when the heatsink temperature falls to 55°C. The fan runs for about a minute after
receiving the stop command or switching on the power, as well as after changing the value from “Continuous” to “Temperature”.
3 First Start—after power up the fan is stopped until the run command is given and then fan runs continuously. This is mainly made
for common DC bus systems to prevent cooling fans to load charging resistors on power up moment.
4 Calc Temp—starting of cooling fan is based on calculated IGBT-temperature. When IGBT temperature = 40°C, fan starts and
when temperature falls down to 30°C, fan stops.
Note: The fan runs continuously, regardless of this setting, when the SVX9000/SPX9000 is in RUN state1203-CN1端子模块英文说明